How wide is a Ford 8.8 rear end?


How to Identify, Construct, and Install the Ford 8.8 Mustang Rearend (with Pictures).

Vehicle Application Axle Width (inches) ’86-’93 Vehicle Application Ford Mustang 8.8 59 11/44 (10.8 59 11/44)


’65-’66 Mustang 57 11/44 from 1967 to 1970 Mustang 8.0 59 51/48 (59/48)


How wide is the back end of a Ford Explorer 8.8 when all of this is taken into consideration?

Axle Dimensions for the Ranger from 1983 to 1992 WMS-WMS 56-1/2 inches 7.5-inch Axle Explorer 8.8-inch Width WMS-WMS 56-1/2 inches 59 and a half inches

Axle tube diameter (1983-2009 models): 2.80 inches 3.25 inches Pinion offset right of centre unk 2 inches Axle tube diameter (1983-2009 models): 2.80 inches 3.25 inches


In addition, how wide is the back end of a Ford 9-inch pickup truck?

Axle type: semi-floating, 56″ overall width, 9 inch ring gear, Ford 9″, rear position, semi-floating axle type, 9 inch ring gear size.


Also, can you tell me how to tell whether I have a Ford 8.8 rear end?

The Ford 8.8-inch rear may be distinguished from other models by its rear cover. It features a 10-bolt cap made of thin metal or plastic, and the bolts have a 7/16-inch thread pitch. Because the cover is not exactly square, it measures about 101/2 inches high by 11 inches wide and 11 inches long. The 8.8-inch pinion shaft has 30 splines and measures 15/8 inch in diameter.


What is the width of the back end of a Ford Explorer?

Outside Width Year Model 58.50 1977-1981 Outside Width Year Model 58.50


Ford Ranger 8.8 from 1993 to 2009 “59.25 59.25

Cougar 59.81 seconds 1967-1970 Mustang, Fairlane, Comet, Fairlane

Ford Explorer 8.8 from 1995 to 2003 “Disc Brake with 31 Splines


There were 33 related questions and answers found.


What is it about the Ford 9-inch rear end that makes it so popular?

There is greater tooth contact between the ring and the pinion because the pinion sits so low on the ring gear. The nose bearing on the pinion also contributes to the overall strength of the gear assembly. The Ford 9-inch axle has more gear ratios available to it than any other axle on the market.


What is the strength of a Ford 8.8 rear end?

The diameter of the pinion-shaft is another factor to consider for strength. When it comes to 1.625 inches, the 8.8 and the 12-bolt are very similar and in fact utilise the same pinion bearings. How to Identify, Construct, and Install the Ford 8.8 Mustang Rearend (with Pictures). AXLE STRENGTH CHART Rear Spline Axle Strength Chart Ford 8.8 28 – 19.3 percent in terms of strength (weaker) General Motors 12-bolt 30-inch Baseline


What is the best way to measure the width of a rear end?

How to Measure the Width of the Rear End The axle flanges should be located on either side of the rear axle. This is the platform on which the wheels are mounted and fastened to the axle, and it is made of steel. Using a measuring tape, measure the distance between one flange and another. Always measure from end to end where the wheels are bolted to the axle to obtain an accurate measurement.


What is a Ford rear axle with an 8.8 ratio?

The 8.8 has a C-clip rearend, which is a huge weak spot because if you break one axle, it may come out of the housing, causing you to lose the wheel and, more than likely, the quarter panels as well. C-clip-eliminator kits, which are available from the aftermarket, are designed to keep the axles in place by attaching flanges to the ends of the axletubes.


What is a Ford 9-inch rear axle, and how does it work?

This axle is a semi-floating, drop-out version of the Ford 9 inch housing. Because of their robustness, these 9-inch rear ends may be found in almost any make and model of automobile, not only Ford vehicles. What distinguishes Ford 9-inch axles from other high-performance rear ends is the manner in which the ring and pinion gear is accessible and engaged.


What cars are equipped with a Ford 8.8 rear end?

Applications That Are Frequently Used Ford Mustang from 1986 until 201Ford F-150 pickup trucks from 1982 to 201Ford Bronco from 1982 until 199Ford Explorer Sport Trac models from 2001 to 200Models of the Ford Ranger 4.0L from 1991 to 201Ford Explorer from 1991 to 2001 (Solid axle) Ford Panther platform cars from 1985 to 2011.


What is the strength of a Ford 7.5 rear end?

Yes, the 7.5 can handle 400 rwhp, but that’s coming near to the limits of its capabilities. A good rule of thumb is around 350 rwhp. The installation of a new rear end is not the first thing that has to be done.


What is the best way to identify my Ford rear differential?

Located next to the driveshaft mount on the passenger side of the housing, facing forward, is a differential carrier tag that carries the Dana model number, as well as other information. In the upper right hand corner of the tag, there is a model number, such as J210-S, which indicates the particular model. Locate the identifying tag on the rear end units that were made by Ford.


Is the Ford 8.8 carrier the same as the others?

For Ford 8.8s, the gear ratios are all the same. The carriers are typically available in two different sizes, which are determined by the gear ratio. Because a complete locker will be used to replace the spider gears, the spline count must be the same as the spider gears.


What is the best way to detect a differential?

In the absence of an ID tag, differentials are recognised by the number of cover bolts, the characteristic form of the cover, the number of ring gear bolts, and the diameter of the ring gear itself. They may also be distinguished by the fact that the central piece is either an integrated or a dropout construction.


How much power can a Ford 7.5 tote about with ease?

“All V6 Mustangs are equipped with 7.5-inch rear ends that include an open carrier differential as standard. They are capable of handling around 300 horsepower. It is possible to break even if you do not have 300 horsepower by using sticky tyres, such as slicks, and launching at high rpms.”