How do I reset my Whirlpool Cabrio touchscreen?

Answer

Instructions for Resetting a Whirlpool Cabrio

If an error code is shown, tap any key on the display pad to clear it, or press “Pause/Cancel” to stop the game.

To begin, choose a new cycle and hit the “Start” button.

If the error or issue continues, turn off and unplug the Cabrio from the power source.

Wait a few minutes before turning on the power again.

If the device is not able to be reset, contact Whirlpool for help.

 

How does one go about resetting a Whirlpool Cabrio while keeping this in mind?

Whirlpool Cabrio Washer Reset Instructions

Turn the washer off if it is still running.

Set the NORMAL setting on the mode selection dial.

The dial should be turned counter clockwise ONE click (to the LEFT), clockwise THREE clicks (to the RIGHT), counter clockwise ONE click (to the LEFT), and finally clockwise ONE click (to the RIGHT) (RIGHT).

Now, hit the start button to begin the process.

 

Similarly, how do you reset a Whirlpool washing machine?

Remove the washer from the electrical socket for 1 minute and then plug it back in.

Reconnect the washer and elevate and lower the top six times in a 12-second interval to complete the task. The lid must be lifted and lowered within 30 seconds of the start time.

This means that the motor has been reset and it is now ready for you to begin a cycle.

 

Is there a reset button on a Whirlpool Cabrio dryer, taking this into consideration?

It is necessary to reset and restart your Whirlpool dryer if it shows the “PF” error code, which indicates that there has been a recent power loss. This is accomplished by pushing and holding the “Start” button for a few seconds to restart the dryer. If the dryer does not restart on its own, pick a new cycle and any additional choices before pressing “Start” to begin the process.

What is the best way to troubleshoot a Whirlpool Cabrio washer?

All contact surfaces on the lid and the washer should be thoroughly cleaned. To reset the control panel, try disconnecting the washer and plugging it back in. Reconnect the washer and check to see whether the issue has been resolved.

Problems with the lid lock

Hold the button down for 3 seconds.

Hold the release button for 3 seconds

Hold the button down for 3 seconds.

Hold the release button for 3 seconds

Hold the button down for 3 seconds.

Release.

What does the Code F on a Cabrio washer stand for?

The F/dL error number on the machine indicates that the door lock has failed. When the door does not lock properly to let the cycle to begin, the door tries to lock itself at least six times before the problem message shows on the digital display screen of the machine. When the door does not lock properly, the machine will not operate at all.

 

What does the code f1 on a Cabrio dryer mean?

When there is a communication breakdown between the control board and the remainder of your machine, the F1 error on your Whirlpool Cabrio dryer will illuminate.

 

What is the proper way to calibrate a Whirlpool Cabrio?

CALIBRATION CYCLE FOR THE CABRIO WASHER Choose three buttons (do not use the Power button) and press them all within eight seconds. In order to do this, ensure that the washer is in (Stand By Mode), which means that it is plugged in and that all of the indication lights are turned off. Press and hold the first chosen button, then press and hold the second selected button, and so on.

 

What should I do if I get an error code on my Whirlpool Cabrio washer?

EXPLAINATION OF THE WHIRLPOOL CABRIO WASHER ERROR LD Maintain the pump and drain hose to ensure that they are free of any debris that might create a clog. The impeller on the drain pump should not be unsteady or broken, so replace it if necessary. Remove the tub hose that connects the pump to the tub and inspect it for obstructions. Check to see that the pump is working and receiving the right voltage at the times that they should be.

 

When it comes to washing machines, is there a reset button?

The motor of certain machines may be reset by pressing a button on the machine. When a machine does not have a reset button, disconnecting the washer and then putting it back in is a common method of resetting it. Although not typically equipped with a button, some programmable washing machines may have a reset function or position that can be used to clear a programming error.

 

What does the letter F stand for on a Whirlpool washer?

The “F” error code indicates a problem with the washing machine’s system, also known as “Fault.” The “E” error code indicates which component in your washer is producing the problem or “Error.” Generally speaking, these “F” error codes indicate the following… – The F5 error number on a Whirlpool Duet washing machine indicates that the door lock and door switch are not working properly.

 

What is the best way to reset my washing machine?

Resetting the washing machine is simple: To turn off the washer, press the POWER button. Alternatively, unplug the washer from its power outlet or turn off the circuit breaker that serves the unit. While the power is turned off, press and hold the START/PAUSE button for 5 seconds to initiate the process. Reconnect the washer’s hoses or reset the circuit breaker if necessary.

 

The code “f1” on a Whirlpool Cabrio washer stands for what?

Whirlpool Cabrio displays an F1 error code, which indicates that the control board is having difficulties communicating with the motor. You can try unplugging your washing machine for 15 minutes and then plugging it back in to see if that helps to resolve the F1 error. It may be necessary to replace the control board if this does not resolve the problem.

 

What is causing my Cabrio washer to not spin?

If your washer does not spin or pump water out, but the motor is still running, it is likely that the pump pulley has frozen. If this is the case, you will need to replace the pump. To inspect the pulley, remove the pump from the washer and manually rotate the pulley to see if it is turning. If it does not turn freely, if it is frozen or stiff, it should be replaced.

 

What should I do if I receive an SD error on my Whirlpool Cabrio?

This will be attempted by the washer by increasing the rinse time in order to clear the suds; if it is successful and no more drag is detected on the tub, the Cabrio Washer Error SD code will be removed from the display. If the error continues to occur, the steps to take in order to attempt to resolve the problem are listed below.

 

When I look at my Whirlpool Cabrio washer, I see the UL code.

UL error code on a Whirlpool Cabrio washer. UL error code for the Cabrio Washer indicates that the load is unbalanced or off-balanced, and it indicates that the control has detected that the tub is out of balance during the spin cycle.