Headlines
Loading...
How does SLT work in MIPS?

How does SLT work in MIPS?


Answer

"Set If Less Than" is an assembly instruction on the MIPS processor that stands for "Set If Less Than." If a value is smaller than another value, the Slt instruction in MIPS will set the value of the corresponding register, and vice versa. It may be used with either a register or an immediate value, depending on the situation (Slti).

 

As a result, what is the best way to save word work in MIPS?

MIPS, please explain how the Store Word(SW) and Load Word(LW) commands function. In the SW, they conduct the operation MEM[$s + offset] = $t, but in the data-path, it seems that they have done the operation MEM[Data($s)+ offset] = $t, since instead of taking in the value $s as an input into the ALU, they have taken in the data stored in the variable $s.


Second, what exactly does XOR in MIPS do?

The XOR Instruction is a combination of two words. Only in the case of a difference between the bits from the operands does the XOR operation change the resulting bit to 1. Whenever the bits from the operands are the same (either both 0s or both 1s), the resulting bit is set to 0. When an operand is XORed with itself, the operand is changed to 0. This is used to clear the contents of a register.


In addition, how does Addi function in MIPS is a question.

The ADDI instruction performs an addition on both the contents of the source register and the immediate data, and then saves the result in the destination register, which is the result of the addition. For example, ADDI $destination register's address is followed by $source register's address and immediately after that is the immediate data.


What exactly does SLT stand for in MIPS?

If the value is less than


What is the reason for the absence of SUBI in MIPS?

The MIPS designers concluded that there was no need for subi (since you can add a negative number with addi by utilising 2's complement), therefore they simply decided not to include it in the instruction set altogether. It might have been done to save on the amount of instructions, or it could have been done simply because it isn't required.

 

What is the meaning of add immediate?

add is a function that adds the values in two registers. addi is a function that inserts an instantaneous value (constant) into the register. This will serve as an example.

 

What is the meaning of a term in MIPS?

In computing, a word refers to the maximum number of bits that may be sent on the data bus at one time and stored in a register at the same time. In the case of MIPS, a word is comprised of 32 bits, or four bytes. Words are always stored in a sequence of successive bytes, with the first byte beginning with an address that is divisible by four.

 

What is the meaning of load higher immediate?

lui stands for "load upper immediate," with "upper" denoting the upper 16 bits and "immediate" denoting that you are providing a literal value to the command line (4097). When 4097 is used as a "upper" value, the result is 0x10010000.

 

What is the role of SRL in MIPS?

A register value is moved to the right by the amount specified in the shift amount (shamt) and placed in the destination register using the SRL logical description. The zeroes have been swapped in.

 

What is the size of a word in bytes?

2 kilobytes

 

What is the total number of MIPS instructions?

MIPS System Call and Breakpoint are the two commands that software may use to trigger an exception in my code.

 

What method do you use to divide in MIPS?

Div is used for signed division, while divu is used for unsigned division when dividing a number. In this scenario, the reminder will be stored in the HI special register, and the quotient of the division will be stored in the LO special register.

 

What is an instantaneous MIPS, and how does it work?

It is possible to address one operand as a constant inside the instruction itself when using MIPS instantaneous addressing.