What size board will a 10 inch sliding miter saw cut?


Answer

A saw with a 10-inch blade can make right-angle cuts across a board that is 5 1/2 inches wide, which is sufficient for two-by-six wood. With the same 10-inch circular saw, you can cut a two-by-four in half at a 45-degree angle as well. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.

 

Likewise, many question, would a 10 inch sliding mitre saw cut a 4×4?

A 44 piece of wood can be cut with the 10-inch mitre saw, which is the maximum cutting capacity of the tool. But to do so it will pass some hard time. You will not be able to cut a 4×4 in a single swing if you are using a stationary mitre saw with a 10-inch blade.

 

In the same vein, do I require a 10 inch or a 12 inch mitre saw?

The 10-inch mitre saw is pretty popular and with good reason. An 11-inch blade will spin more quickly than an 11-inch blade, which will result in smoother cuts. The 10-inch blade will have a higher RPM rate due to the equal powering of the two motors, and higher RPMs will result in a finer finish due to the higher RPMs.

 

As a result, the question of how wide a sliding mitre saw can cut may also arise.

The sliding saw can extend its reach out to 12 or even 16 inches, more than double the breadth of a non-slider. If you’re routinely working with boards this wide, you will thank yourself every day for buying the sliding mitre saw. Furthermore, because you’re only cutting once, all of your cuts will be cleaner and more precise as a result.

 

How thick can a 10 table saw cut?

The blade raising mechanism on most saws can raise the arbour until the flange almost touches the underside of the throat plate, which is usually about 1/8 inch thick. Generally speaking, a 10 inch saw can cut slightly over 3″ deep. A 12 inch saw will cut 4 inches deep.

 

32 Related Question Answers Found

 

Is a sliding mitre saw worth it?

It’s definitely worth the investment if you know you’re going to use it but if you’re not sure about the kind of work you’ll be doing, a sliding mitre saw might not be necessary. Another downside to sliding mitre saws is they need a lot more space than a compound mitre saw.

 

Can a 10 inch mitre saw cut a 2×8?

Typically, a 10-inch mitre saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch mitre saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees. The sliding action can cut even wider boards.

 

Can you use a mitre saw like a table saw?

A mitre saw is similar in conception to a table saw in that it utilises a rotating circular saw blade to cut wood. However, a mitre saw is meant for a very specific purpose, while a table saw is a general purpose wood cutting tool. Miter saws are specifically designed to make accurate crosscuts and angular cuts.

 

What size of mitre saw do I need?

Unless you are cutting very large baseboards, I would recommend sticking with a 10 or 12-inch mitre saw. A 10-inch mitre saw can very easily and very accurately cut 6-inch baseboards. However, if you already have a 12-inch mitre saw, that is perfectly fine for cutting baseboards.

 

How deep can a 10 inch circular saw cut?

It features a 60-degree bevel capacity that helps in a variety of tasks. Even at maximum bevel, the saw reaches a cut depth of 1-3/4 inches. It also includes an electric brake for quick blade stoppage.

 

How do you know what angle to cut wood?

The formula involves dividing 360 by the number of sides to calculate the corner angle. Then divide it by two to get the mitre angle. If you’re making a five-sided project with all sides equal, you divide 360 by five to get 72 degrees. So each joint or corner forms a 72-degree angle.

 

Should I buy a table saw or mitre saw?

When it comes to this face-off, should you buy a table saw or a mitre saw? A table saw can make longer cuts, while a mitre saw excels in making short, bevelled and angled cuts. A Table saw can make those same cuts if you have a jig, but it is more cumbersome.

 

Can you rip with a mitre saw?

You can’t use a rip blade for on a mitre saw because the design of a mitre saw is such that wood lays across its blade path and not along it. For this reason, you will not use a mitre saw for ripping. Miter saws are powerful tools because they transcend regular carpentry jobs like cutting two-by-fours.

 

What’s the difference between a compound mitre saw and a sliding mitre saw?

The main difference between a sliding compound mitre saw and a compound mitre saw is the rail or rails on the sliding saw. These rails allow you to slide the saw back and forward as you cut. The saw can do everything that a compound mitre saw can do. This saw allows you to cut materials that are up to 16 inches thick.