What does f2 mean on Kenmore Elite washer?


The F2 fault code indicates that there is an issue with the washer’s drain system, and you must investigate the problem in order to discover how to repair the washer and remove the fault code.

What does the f2 symbol on a washing machine indicate was also a question. 

Whirlpool’s F2 error code is denoted as F02, and it indicates that the washer is taking an excessive amount of time to adequately drain its contents. If this occurs, it indicates that there is some kind of issue with the washer’s drainage mechanism.


Second, how can I get rid of the error code on my Kenmore washing machine?

The code must be reset by unplugging the washer’s power source from the wall outlet.

On the washer’s control panel, look for the “Pause/Cancel” button to press.

To cancel the wash cycle, press the “Pause/Cancel” button two more times.

While the washer is not in use, inspect the water supply pipe for kinks or other obstructions.


So, what exactly does the code f02 on my Kenmore Elite washer mean?

On a Kenmore HE3 washer, the F02 error number signifies that the control system has detected a prolonged drain time. A buildup of suds in the tub, a blockage or restriction in the drain system, or a variety of other component problems may all cause this.


What is the best way to reset my Kenmore Elite washer?

Instructions for Resetting a Kenmore Elite HE Washer

Press the “Stop” button twice, and then press the “Power” button to turn the computer off and on.

You may start by selecting a wash cycle (for example, “Normal”) and then selecting your wash choices (for example, “Hot/Cold” or “Cool/Cold”).

In order to finish the reset procedure and restart the washing machine, press and hold the “Start” button.

There were 38 related questions and answers found.

What does the error code f2 indicate?

The oven temperature sensor, sometimes known as the thermistor, is the source of the F2 error number on a microwave range. thermistor has been short-circuited and is consequently not functioning, according to F2. It does not mean that the thermistor is at fault in every instance. It’s possible that the wire harness is at blame.

What does the letter F stand for on a washing machine?

There was a component fault identified by the washer control, as indicated by the F. Because the door remained locked, it is probable that the issue was with the drain pump or that excessive suds were preventing the washer from adequately emptying the water.

What is the procedure for resetting the code on a Whirlpool washer?

Once you have pressed the Start Stop button, you are finished. The Rinse, Wash, and Stop lights should all be illuminated after rotating the dial. Turn off the washer and disconnect it for 10 seconds to allow the water to drain. Finally, switch on the washer, and the machine should be back in working order.

How do you interpret the f2 code on your oven?

If you have a GE oven, the error number F2 on the oven implies that the temperature sensor has detected a temperature that is higher than the threshold specified by the oven manufacturer. If you have a GE oven, the error number F2 on the oven implies that the temperature sensor has detected a temperature that is higher than the threshold specified by the oven manufacturer.

What does the letter F on my Whirlpool washer stand for?

The “F” error number indicates a problem with the washing machine’s system, sometimes known as “Fault.” The “E” error code indicates which component in your washer is producing the problem or “Error.” Generally speaking, these “F” error codes indicate the following… – Dishwasher Whirlpool Duet Washing Machine The F5 error number indicates that there is a problem with the door lock or door switch.

What does the Sud symbol on a Whirlpool washer mean?

On the display of your Whirlpool Washer, you will see “Sud” or “Sd.” This error number indicates that there was an excessive amount of detergent suds produced throughout the cycle. This might be caused by the use of excessive detergent or the failure to use High Efficiency (HE) detergent. The washer will not be able to spin off water because of the surplus suds that has accumulated.

Dexter commercial washers have an error code of f2. What does this mean?

When the F2 error code is shown, the water levels are low, regardless of the temperature of the water. Cleaning and inspecting the water inlet screens and hoses.

What is the best way to clean a Kenmore Elite washing machine?

How to Clean a Kenmore Elite Front Load Washer (with Pictures) Open the washing door and take out any garments that may have been trapped within. Open the dispenser drawer and pour a total of 2/3 cup chlorine bleach into the dispenser. The “Cycle” button should be pressed a couple of times until the “Clean Washer” cycle is chosen. To begin, press “Start.” After the cycle is complete, open the door and leave it slightly ajar to allow the washer to finish drying.

What is the best way to reset my Kenmore front-load washer?

To conduct a Master Reset, gently disconnect the washing machine from the power socket and keep it unplugged for one minute until the process is complete. After the one-minute timer has expired, reconnect the washer cable to the wall. Then, within 12 seconds, open and shut the door of the washing machine six times to transmit a “reset” signal to all of the components.

What should I do if my Kenmore Elite washer is giving me the Sud error?

This might be caused by a faulty pump, an excessively heavy load, an excessive amount of detergent, or an excessive amount of suds. If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. This should help to empty the unit of any remaining detergent.

What does the Sud symbol on a Kenmore Elite washer represent?

It is possible to have too much suds for the washer to remove when the Sud error code is shown. This is often caused by the use of excessive amounts of detergent or the use of non-HE detergent in a HE machine.

What does the code f2 on a Kenmore oven mean?

The “F2” error code indicates that the oven became too hot. Allowing the oven to cool completely before reconnecting the power connection is recommended. When the oven is chilly, the display of “F2” may indicate a malfunctioning electronic oven control board or a malfunctioning oven temperature sensor probe.